#SPARKBOX GENERATOR INSTALL#If you have a turbo car, make certain that the speed relay did not cause the failure of the original ignition box before you install the new box. Please contact the factory for technical and warranty assistance. The dealer you purchased your Perma-Tune from is not authorized to issue warranty replacement or exchange units. In either case contact Perma-Tune for assistance with exchanges. If the connector does not match that of the car, you have the wrong unit for that car. If you are installing a 911SC engine in a 911 body, use the model 911902EX Engine Exchange kit. If you need a harness to install this ignition system, exchange it for a Model MP Perma-Tune. The Model 911SC902 Perma-Tune is designed to replace the stock ignition box and will bolt up and plug in to the same location as the stock system. 065â€, (except on turbo charged cars with special spark plugs that cannot be re gapped) and solid core, unshielded copper spark plug wire can be used without causing radio noise problems. This increase in spark energy improves combustion efficiency resulting in more performance and less unburned fuel in the exhaust. #SPARKBOX GENERATOR UPGRADE#The Model 911SC902 is more than a replacement of the original ignition system it is a performance upgrade boosting the spark energy by a factor of three. If this is the case we recommend you refer to the technical and diagnostic guide in the technical support section of the Perma-Tune web site. Wiring problems external of the unit will cause your Perma-Tune to get hotter to the touch than the other components under the hood. #SPARKBOX GENERATOR MANUAL#Verify ignition timing according to the shop manual and engine bay placards for this car.īy design, Perma-Tune ignitions make very little heat of their own. Note: To avoid potential damage to your new ignition box, we recommend that you perform the ground loop test described on our web site technical support page before plugging in a new ignition box.Ĥ. If the tests indicate a fault exists, repair any fault that may exist in the vehicle, and then plug in the module. Before plugging in the connector, perform the distributor signal test and the ignition module ground test. Bolt the ignition box to the relay panel. Plasmatronics part number SC010 ignition coil is recommended for use with all Perma-Tune ignition systems.ģ. Note: To avoid potential damage to your new ignition box, we recommend that you replace the ignition coil when the ignition box is replaced. Replace the coil if the coil does not test to specifications or if there is evidence of oil or tar leaking from the coil. Perform an ignition coil resistance test. Failure to reconnect this ground strap may result in damage to the car or your new ignition box.Ģ. It is extremely important that this ground strap be reconnected when the relay panel is bolted back to the car. This ground strap can be easy to forget to hook back up because when it is removed from the relay panel it will fall forward between the fuel filter and fuel accumulator where it cannot be seen. One of the screws for the relay panel mounting also holds the braided ground strap that provides the ground for the relay panel. NOTE: On some cars, the relay panel where the ignition box is located must be unbolted from the car so that the nuts can be held while the bolts for the ignition box are unscrewed. Perform any maintenance procedure needed, if the bench check procedure indicates so, to prevent damaging the new ignition module upon its installation. Perform a bench check of the module according to the manufacturers specifications. Remove the old ignition module from the car according to the shop manual for this car. O Flying lead connector for easy installation and maintenance.ġ. O External, repairable, fusible link to protect the vehicle and Perma-Tune from ground loop damage. O Black anodized housing that resists corrosion and is paint able. O Larger housing to accommodate more robust, reliable components. The Model 911SC902 supersedes the Model 911SC Perma-Tune and has many improvements over the older model: New features of the Model 911SC902 Perma-Tune This part is designed to be installed by a mechanic that is familiar with European automobiles and safety standards. #SPARKBOX GENERATOR HOW TO#Installation Instructions on how to install a new Porsche 911 6 pin Spark Box or CDI unit.ĭISCONNECT THE BATTERY BEFORE INSTALLING OR SERVICING ANY IGNITION SYSTEMS COMPONENTS.įailure to follow these instructions and the vehicle owners handbook and shop manual could result in serious personal injury, death and or damage to property. By design911 on Thursday, November 11, 2010
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |